CPH6622 no. a0398-1/4 features low on-resistance. 2.5v drive. best suited for lib charging and discharging switch. common-drain type. w ith a built-in gate resistor. specifications absolute maximum ratings at ta=25 c parameter symbol conditions ratings unit drain-to-source voltage v dss 20 v gate-to-source voltage v gss 12 v drain current (dc) i d 3.0 a drain current (pulse) i dp pw 12ms, duty cycle 1% 18 a allowable power dissipation p d mounted on a ceramic board (900mm 2 ? 0.8mm)1unit 0.9 w t otal dissipation p t mounted on a ceramic board (900mm 2 ? 0.8mm) 1.0 w channel temperature tch 150 c storage temperature tstg - -55 to +150 c electrical characteristics at ta=25 c ratings parameter symbol conditions min typ max unit drain-to-source breakdown voltage v (br)dss i d =1ma, v gs =0v 20 v zero-gate voltage drain current i dss v ds =20v, v gs =0v 1 a gate-to-source leakage current i gss v gs = 8v, v ds =0v 10 a cutoff voltage v gs (off) v ds =10v, i d =1ma 0.6 1.2 v marking : bw continued on next page. tokyo office tokyo bldg., 1-10, 1 chome, ueno, taito-ku, tokyo, 110-8534 japan ordering number : ena0398a specifications of any and all sanyo semiconductor co.,ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer ' s products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. any and all sanyo semiconductor co.,ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, av equipment, communication device, office equipment, industrial equipment etc.). the products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. if you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. if there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. 80807 ti im / 71807pe ti im tc-00000813 sanyo semiconductors d ata sheet CPH6622 n-channel silicon mosfet general-purpose switching device applications
CPH6622 no. a0398-2/4 continued from preceding page. ratings parameter symbol conditions min typ max unit forward transfer admittance ? yfs ? v ds =10v, i d =1.5a 1.5 3.3 s static drain-to-source on-state resistance r ds (on)1 i d =3a, v gs =4v 46 58 70 m ? r ds (on)2 i d =3a, v gs =2.5v 50 75 100 m ? t urn-on delay time t d (on) see specified test circuit. 210 ns rise time t r see specified test circuit. 690 ns t urn-off delay time t d (off) see specified test circuit. 1400 ns fall time t f see specified test circuit. 1000 ns t otal gate charge qg v ds =10v, v gs =4v, i d =3a 10.5 nc gate-to-source charge qgs v ds =10v, v gs =4v, i d =3a 1.0 nc gate-to-drain ?iller?charge qgd v ds =10v, v gs =4v, i d =3a 2.8 nc diode forward voltage v sd i s =3a, v gs =0v 0.8 1.2 v package dimensions electrical connection unit : mm (typ) 7018a-013 switching time test circuit pw=10 s d.c. 1% p. g 50 ? g s d i d =1.5a r l =6.67 ? v dd =10v v out CPH6622 v in 4v 0v v in rg=1k ? rg 1 : source1 2 : drain 3 : source2 4 : gate2 5 : drain 6 : gate1 t op view 6 2 54 13 1 : source1 2 : drain 3 : source2 4 : gate2 5 : drain 6 : gate1 sanyo : cph6 3 2 1 64 5 2.9 0.05 0.4 2.8 1.6 0.2 0.6 0.6 0.9 0.2 0.15 0.95
CPH6622 no. a0398-3/4 i d -- v ds i d -- v gs drain-to-source voltage, v ds -- v drain current, i d -- a gate-to-source voltage, v gs -- v r ds (on) -- v gs r ds (on) -- ta static drain-to-source on-state resistance, r ds (on) -- m ? gate-to-source voltage, v gs -- v static drain-to-source on-state resistance, r ds (on) -- m ? ambient temperature, ta -- c drain current, i d -- a ? y fs ? -- i d i s -- v sd drain current, i d -- a forward transfer admittance, ? y fs ? -- s diode forward voltage, v sd -- v source current, i s -- a sw time -- i d switching time, sw time -- ns drain current, i d -- a it10968 1000 100 3 2 5 7 2 3 0.1 1.0 23 57 23 57 t d (off) t f t d (on) t r v gs -- qg t otal gate charge, qg -- nc gate-to-source voltage, v gs -- v 010 9 368 257 14 3 10 0 1 4 it12758 8 9 5 6 7 2 v ds =10v i d =3a 0246810 it12754 150 0 50 100 t a=25 c i d =3a it12756 it12757 0 0.2 0.4 0.6 0.8 1.0 1.2 0.01 0.1 7 5 3 2 2 7 5 3 2 1.0 5 3 v gs =0v - -25 c 25 c ta=75 c 1 3 2 0 0 1.0 0.5 2.0 1.5 2.5 3.0 it12753 25 c v ds =10v t a=75 c - -25 c 0 0 1 2 3 0.5 0.1 0.2 0.4 0.3 it12752 v gs =1.8v 2v 2.5v 4v 6v 8v 3v 0.1 1.0 2 1.0 357 23 7 5 3 2 75 c t a= --25 c 25 c v ds =10v it12755 - -100 0 50 100 150 - -50 0 150 100 50 200 v gs = 2.5 v, i d = 3 a v gs = 4.0 v, i d = 3 a
CPH6622 no. a0398-4/4 ps sanyo semiconductor co.,ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all sanyo semiconductor co.,ltd. products described or contained herein. sanyo semiconductor co.,ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. it is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. when designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of sanyo semiconductor co.,ltd. or any third party. sanyo semiconductor co.,ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equipment, refer to the "delivery specification" for the sanyo semiconductor co.,ltd. product that you intend to use. in the event that any or all sanyo semiconductor co.,ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of sanyo semiconductor co.,ltd. note on usage : since the CPH6622 is a mosfet product, please avoid using this device in the vicinity of highly charged objects. this catalog provides information as of august, 2007. specifications and information herein are subject to change without notice. ambient temperature, ta -- c allowable power dissipation, p d -- w p d -- ta a s o drain-to-source voltage, v ds -- v drain current, i d -- a 100ms dc operation (t a=25 c) 1ms i dp =18a 2 2 3 5 7 0.1 2 3 5 7 1.0 0.01 23 57 2 0.01 0.1 357 2 1.0 it12703 i d =3a it12704 100 s 10ms 0 0 20 40 60 80 100 120 0.2 0.4 0.6 0.8 0.9 1.0 1.2 140 160 1unit 2 3 5 7 10 3 5 357 2 10 3 mounted on a ceramic board(900mm 2 ? 0.8mm)1unit t otal dissipation operation in this area is limited by r ds (on). t a=25 c single pulse mounted on a ceramic board (900mm 2 ? 0.8mm) 1unit pw 10 s
|
